Cement Testing Equipment

We are trusted name in manufacturing CBR mould which are superior in quality and deliver a highly rated performance. These are made of high quality metal and very strong so that it can resist distortion. These moulds even retain their shape and size even under rugged conditions.

We manufacture the proctor compaction mould as per ref Stds : IS 2720 (Part 7), IS 2720 (Part 8), IS 9198, IS 10074, BS 1377 ASTM D 698 and ASTM D 1557. Supreme quality metal is used so that it is enough strong to resist distortion & retain their shape and size even under rugged and extreme conditions.

We are engaged in offering moulds of varied sizes for cube, beam & cylindrical moulding which are required for compressive strength testing. Our premium moulds are made of high quality metal.These are strong in design and enough to resist distortion & retain their shape and size even under rugged conditions.

The apparatus comprises one each of permeability Cell “U” tube manometer with stop cock mounted on a laminated wooden stand, perforated metal disc, plunger, Rubber, Stopper, Rubber tube with rubber bulb.

Spares :

• Laminated wooden stand with ‘U’ tube monometer with stop cock.
• Permeability Cell complete with perforated metal disc, non -perforated disc and plunger.

It consists of a small split cylinder forming a mould on either side of the split cylinder, two parallel indicating arms with pointed ends are attached.

Supplied complete with two glass plates and lead weigh

The autoclave is suitable for conducting accelerated soundness test on cements or the autoclave expansion test requiring constant steam pressure with the correspondent constant pressure. It is consists of a stainless steel cylinder with a welded heat insulated voer, mounted on a sturdy supporting frame, enclosed in a heat insulated metal housing, attractively finished. The attached control unit encloses sensitive pressure regulator and pressure gauge, power switches and pilot lights for controlling the electric heating units inside Chamber Dimension-15 cm dia meter x 40.5 cm height suitable for operation on 230 v, 50 hz, Single phase, A.C. supply.

Supplied complete with test bar holder Special rack to hold specimens above water level in the autoclave and in vertical position to expose them in the same manner.

For determination of consistency of standard cement paste and initial and final setting times of cement. The equipment comprises the following :-

• A frame with a vertically movable rod having a cap at the top.
• Vicat mould in the form of frustum of a cone with internal diameter of 60 mm at the top, 70 mm at the bottom and a height of 40 mm.
• Glass base plate for the mould.
• Initial setting time needle.
• Final setting time needle.
• Consistency plunger.

Accessories:

• Setting time needle.
• Final setting time needle
• Consistency plunger.
• Vicat mould

It is used for determining the workability of building lime.
It comprises :

• One 300 mm dia polished steel table with three engraved circles of 70 mm, 110 mm and 190 mm dia at the top face.
• A frame having a horizontal shaft carrying a cam on one side and a wheel on the other, adjusted to raise the table by 12.5 mm and allow it to fall freely.
• Truncated conical mould 65 mm inside dia at the bottom, 40 mm inside dia at top and 90 mm high.

Accessories :
 Flow Mould.

It is used for preparation of plastic mortar of cement and pozzolanic materials for making different types of test specimens in the laboratories.
The apparatus comprises the following :-

• A motor-driven mixer which simultaneously imparts two motions to the mixing paddle i.e. revolving and planetary, they being opposite to one another in direction as per IS standards. A two speed gear box is incorporated in the drive which makes the paddle revolve at approximately 140 and 285 r.p.m. with corresponding planetary motion of 62 and 125 r.p.m. respectively.
• A stainless steel mixing paddle of the specified shape and dimensions which can be attached or removed easily.
• A stainless steel mixing bowl of about 6 litre capacity. This can be held with the mixing apparatus and its height is adjustable.
• A scraper made from semi rigid rubber blade attached to a handle about 150 mm long. The blade is about 75 mm long and 50 mm wide.

Suitable for operation on 220v, 50 Hz, single phase supply.